Bay Networks 4000 Przewodnik Instalacji Strona 22
- Strona / 162
- Spis treści
- BOOKMARKI
- Remote Annex 1
- © 1996 Bay Networks, Inc 2
- Revision Level History 3
- Contents 5
- Contents 6
- Figures 10
- Tables 12
- About this Guide 13
- Printing Conventions 14
- Related Documents 15
- Bay Networks Customer Service 17
- World Wide Web 19
- Customer Service FTP 20
- Support Source CD 20
- CompuServe 20
- InfoFACTS 21
- How to Get Help 22
- Remote Network Access 23
- Dial-up Routing 24
- Chapter 1 Introduction 25
- Remote Annex 4000 Description 26
- Main Logic Board 26
- Serial Line Controllers 27
- Asynchronous SLC 28
- Firmware and Software 29
- Supported 30
- Configurations 30
- Watchdog Timer 30
- Front Panel 31
- Front Panel Components 32
- Rear Panel 33
- Rear Panel Components 34
- Mode Jumper 35
- Network Interface 35
- Connectors 35
- Physical Characteristics 36
- 6 in. (15 cm) 38
- Before you Begin 39
- Ethernet cable 41
- Ethernet cable (see 42
- Figure 2-3): 42
- Figure 2-4): 43
- Connecting a Console Terminal 45
- Cable Retainer 48
- PBX End 48
- PBX Screw 49
- Cable Retainer Screw 49
- 50–19,200 250 75 51
- 38,400 200 60 51
- 57,600 100 30 51
- 115,200 50 15 51
- Connecting a Parallel Printer 52
- Power Select Switch 53
- 2 Apply power 54
- 4000 to your LAN 57
- This section describes: 57
- Server. Proceed as follows: 58
- Remote Annex and press 59
- Prerequisites 61
- The system responds: 64
- For example: 65
- For example: 65
- Auto-initializing the ROMs 66
- BOOTP response with the sm 68
- 4 Boot the Annex 69
- Invoking the Console Monitor 70
- Command Descriptions 74
- Command Description Use 76
- (Flash) is installed 83
- Remote Annex 4000 is booted 86
- 4000 ROM Monitor commands 89
- Network test – PASSED 94
- [data bytes] [npackets] 97
- Interface sequence: sl2,net 102
- Prompt Description 104
- Statistic Description 105
- Power-up and Boot Procedures 108
- On continuously 109
- Flashing irregularly 109
- Test Mode Diagnostics 113
- Table 4-4 115
- Boot Failures 117
- Boot Error Report 118
- Error Description 119
- # /etc/erpcd –D5 123
- # boot -v 123
- Another Remote Annex 4000 124
- VAX VMS Load Host on the LAN 125
- ● ● ● ● ● 126
- Console Port 129
- Coaxial Center 130
- Conductor 130
- Coaxial Shield 130
- 10Base5 Ethernet Port 131
- 10BaseT Ethernet Port 132
- Serial Port 133
- Pin Signal Pin Signal 134
- Parallel Printer Port 135
- Serial Port Cables 137
- Remote Annex 4000 Champs 138
- (continued on next page) 139
- Serial Cable Wiring Diagrams 143
- Printer Cables 145
- Dataproducts 146
- Printer Cable 146
- Loopback Connectors 147
- PBX Loopback 148
- Connector 148
- Contents of the Kit 149
- Dress Panel Cover 150
- (10 Places) 151
- (4 Places) 152
- Figure C-6) 153
- Assembly Instructions 155
- Power-up and Test 156
- Test Button 157
- PBX Loopback Plug 158
- Numerics 159
- Index 160
Powiązane produkty i podręczniki dla Oprogramowanie Bay Networks 4000
(47 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji