Bay Networks 5391 Przewodnik Instalacji Strona 52
- Strona / 138
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Remote Annex 6300 Hardware Installation Guide
Chapter 2 Installing the Remote Annex 6300
2-16
If the ATTN LED is ON or flashing, one of the following failures
has occurred (see Chapter 4 for more details):
❑ Remote Annex hardware failure; contact technical
support.
❑ Network or network interface failure; error message
displays on the console.
If a network or network interface failure occurs, typing
q accesses the ROM Monitor prompt. Check the network
connection and then see net on page 3-23.
3 Verify the Remote Annex 6300’s hardware configuration.
At the monitor prompt on the console, type config and press
. The screen display looks similar to this:
This display is typical for T1 versions. For E1,
information, 32 ports will be shown. For versions
without modems, no port or modem information
will be shown.
Retur
n
REVISION/CONFIGURATION INFORMATION
ROM Software Rev: 1002
Board ID: 63 Board Type: RA6300
CPU Type: 486DX2 Ethernet Address: 00-80-2D-02-CE-A9
Memory size: 8 Meg EEPROM size: 65504
Flash size: 2 Meg Flash ID: 8989
Available Interfaces (* = selected) ThickNet ThinNet *Twisted Pair
SLC Local DRAM Size: 4 Meg SLC SRAM Size: 128K
TDM Interface: PRI T1 USA Revision: VERSION A MGR=1.117
Modem Country Code: 63
Port # 1 2 3 4 5 6 7 8 9 10 11 12
Modem ID 2883 2883 2883 2883 2883 2883 2883 2883 2883 2883 2883 2883
Mod Status OK OK OK OK OK OK OK OK OK OK OK OK
Port # 13 14 15 16 17 18 19 20 21 22 23 24
Mod ID 2883 2883 2883 2883 2883 2883 2883 2883 2883 2883 2883 2883
Mod Status OK OK OK OK OK OK OK OK OK OK OK OK
- Remote Annex 1
- © 1996 Bay Networks, Inc 2
- Rules, Part 68 6
- Revision Level History 7
- Revision Level History 8
- Contents 9
- Contents 10
- About this Guide 15
- Printing Conventions 16
- Preface 17
- Convention: Represents: 17
- Related Documents 18
- Bay Networks Customer Service 19
- World Wide Web 21
- Customer Service FTP 22
- Support Source CD 22
- CompuServe 22
- InfoFACTS 23
- How to Get Help 24
- Remote Network Access 25
- Remote Annex 6300 Description 26
- Main Logic Board 26
- Modem Carrier Card 27
- Firmware and Software 27
- ROM Monitor 28
- Supported 28
- Configurations 28
- Watchdog Timer 28
- Front Panel 29
- Front Panel Components 30
- Network/Status 31
- (continued on next page) 31
- The button is used to: 32
- Rear Panel 33
- Rear Panel Components 34
- Physical Characteristics 35
- Before you Begin 37
- Front Mount 38
- (3 places each side) 39
- Rear Mount 40
- Bracket Mounting 41
- (2 Screws each side) 41
- Bracket Assembly 41
- (2 Screws, 2 Nuts, and 41
- 4 Washers each side) 41
- CONSOLE 10BASE5 10BASET 42
- ISDN PRI 42
- ❑ Thin Ethernet (10Base2) 43
- ❑ Thick Ethernet (10Base5) 43
- ❑ Twisted Pair (10BaseT) 43
- Ethernet cable (see 45
- Figure 2-7): 45
- Figure 2-8): 46
- Connecting a Console Terminal 47
- Annex 6300 49
- 2 Apply power 50
- 6300 to your LAN 53
- This section describes: 53
- 3 Execute the boot command 54
- BOOTP response with the sm 56
- Invoking the Console Monitor 58
- Command Descriptions 60
- Command Description Use 62
- Remote Annex 6300 is booted 72
- Remote Annex’s console port 73
- 6300 ROM Monitor commands 76
- Network test – PASSED 81
- [data bytes] [npackets] 84
- Statistic Description 87
- Bay Networks 89
- LED(s) Description 91
- Power-up and Boot Procedures 92
- N1: LEDs OK 93
- N2: Hardware OK 93
- NE2: Hardware Failure 94
- NE5: Booted wrong image 94
- Setup Mode 95
- T1: Testing LEDs 96
- T2: Testing Hardware 96
- T3: At Monitor Prompt 96
- TE2: Hardware Failure 97
- TE7: Booted Wrong Image 97
- Boot Failures 98
- Boot Error Report 99
- Error Description 100
- The broadcast address 101
- The subnet mask 101
- # /etc/erpcd –D5 103
- # boot -v 103
- Another Remote Annex 6300 104
- Remote Annex 6300 Dumps 105
- Annex overwrites crash dumps 106
- Console Port 109
- 10Base2 Ethernet Port 110
- 10Base5 Ethernet Port 111
- 10BaseT Ethernet Port 112
- PRI ISDN Interface 113
- Loopback Connectors 115
- Contents of the Kit 117
- Disassembly Instructions 118
- Installation Instructions 119
- Assembly Instructions 121
- Power-up and Test 122
- Removing Quad Modem Cards 131
- Modem Card 133
- DIP Switch S1 134
- Front of Unit 134
Powiązane produkty i podręczniki dla Oprogramowanie Bay Networks 5391
Oprogramowanie Bay Networks 5000 Instrukcja Obsługi
(166 strony)
(166 strony)
Oprogramowanie Bay Networks 5000 Dokumentacja
(185 strony)
(185 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.090 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji